Racking Board Solutions
Veristic Manufacturing has a wide range of racking boards for any requirement. Our designs focus on improved safety for personnel and enhanced usability. We can provide you with traditional boards, as well as more advanced solutions with remote controlled pneumatic latches and pipe racking systems. Contact us to discuss your next project.
Racking Board System for Drilling Rig
View Specifications
- Heavy Duty Racking Finger Assemblies
- One Telescoping monkey board
- Structural support beams as required to mount Racking Finger Assemblies and Monkey Board to the derrick.
- All racking fingers will have Individual stainless steel latches for every pipe stand. All latches are recessed below the finger and will cause no interference to derrickman's foot.
- Racking board is designed to allow pipes to be racked in any fashion or direction.
- "Kick Lock design" of finger latches will allow derrickman to close or open the latch easily by using his foot. Derrickman will not have to bend down and lock pipe by hand.
- End latches will be provided at each end of fingers for inter-locking between fingers. This generates extra support during the dynamic motion or storm condition. All end latches will be recessed and free from interference with drill pipe during racking operation.
- "Non Slip" working surface on top of each fingers will provide additional safety for derrickman.
- Retractable monkey board enables the derrickman to position himself at the best location to rack pipe with different top-drive.
Power Assisted Racking System
View Specifications
- New approach to handle drill pipes and collars
- Improves Rig efficiency
- Maximum safety design standard
- Minimum weight but strong
- Simple & proven mechanical system
- Retrofitted to new or existing derrick
- Will not stop working!!!
- Ideal for back-up racking system to prevent Rig shut down
- Two Heavy Duty Racking Finger Assemblies designed to fit customer's specifications.
- One Telescopic Monkey Board with manual jacking system for positioning the derrick man at the safest distance from the well center.
- Structural support beams as required to mount Racking Finger Assemblies and Monkey Board to the derrick.
- All racking fingers have Individual stainless steel latches for every pipe stand. All latches are recessed below the finger and will cause no interference to derrickman’s foot.
- Racking board is designed to allow pipes to be racked in any fashion or direction.
- “Kick Lock design” of finger latches will allow derrickman to close or open the latch easily by using his foot. Derrickman will not have to bend down and lock pipe by hand.
- End latches will be provided at each end of fingers for inter-locking between fingers. This generates extra support during the dynamic motion or storm condition. All end latches will be recessed and free from interference with drill pipe during racking operation.
- “Non Slip” working surface on top of each fingers will provide additional safety for derrickman.
Offline Stand Maker
View Specifications
- Lifting System: Lifting winch powered by inverter duty AC electric motors with remote control is designed to be mounted near crown block area for maximum lifting capacity of 5,000 lb. Lifting line shall be 3/4” diameter rotational resistance wire rope with sufficient length to reach drill floor. OSM Elevator is designed to handle specified drill pipe. OSM Elevator includes swivel bearing and hoisting load compensator. The Lifting System remote control is designed with soft stabbing features to protect the pipe thread.
- Steering System: A four way X-Y steering system that provides transitional movement for the lifting line and OSM Elevator. Trolley assembly with four wire line guide rollers travels along the trolley beam that runs transversely on top of two parallel bridge beams. System is powered by inverter duty AC electric motors with rack and pinion gear drive in both directions. Limit switches and structural stops are provided to prevent possible over-travel in all directions.
- Control System: The control system includes three variable frequency drives. All consoles are made of NEMA-4X stainless steel enclosures. One wireless remote control unit is located at floor level for making up the pipe stand and one wired remote control is located at racking board for handling the triple stand pipe. Both remote controls include two joysticks each to operate the steering and lifting system.
Request a quote for a Racking Board Solution or call (281) 879-4571 to speak directly with sales.
